订书机常见故障排除与维修 一、常见故障 1. 订书机卡住 当订书机在订书过程中卡住，可能是由于纸张或其他杂物卡在订书针的出口处。此时，需要拆开订书机，清理内部的杂物。 2. 订书针弯曲或断裂 订书针的弯曲或断裂可能是由于长时间使用或不当使用导致的。这时需要更换新的订书针。 3. 订书机不工作

如果订书机按下后没有任何反应，可能是电源问题或内部零件故障。需要检查电源和内部零件是否完好。

【订书机】晨光省力型订书机办大加厚公用号大型多功能学生用大订书器超大丁售价：57.66元 领券价：57.66元 邮费：0.00

二、维修方法 1. 订书机卡住的维修 首先，要断开电源（如果是电动的），然后小心地拆开订书机。查看订书针的出口处是否有卡住的纸张或其他杂物，如果有，需要清理干净。然后重新组装订书机，再次测试其功能。 2. 更换订书针 当订书针弯曲或断裂时，需要更换新的订书针。首先，找到订书机的订书针更换口，然后取出旧的订书针，插入新的订书针。注意新订书针的规格应与原订书机匹配。 3. 检查电源和内部零件 如果订书机不工作，首先检查电源是否完好。如果是电池供电的，可以尝试更换电池。如果电源正常，那么可能是内部零件出现故障，需要拆开订书机，检查内部零件是否损坏或松动，如有必要，应进行更换或修理。 三、翻译成英文： Troubleshooting and Maintenance of Common Staplers Issues I. Common Issues: 1. Stapler Jamming: Stapler may jam during the stapling process due to paper or debris getting stuck in the stapling needle exit. In this case, disassemble the stapler and clean the debris inside. 2. Bent or Broken Staples: Bent or broken staples may be due to long-term or improper use. At this point, replace the staples with new ones. 3. Stapler Malfunction: If the stapler does not respond when pressed, it may be a power issue or an internal component failure. Check if the power source and internal components are intact.

【订书机】得力10号订书机迷你小号手握式订书器办公小定钉书机器小型携带款售价：59.68元 领券价：59.68元 邮费：0.00

II. Maintenance Methods: 1. Fixing a Jammed Stapler: First, disconnect the power (if it is electric), then carefully disassemble the stapler. Check if there is paper or debris stuck in the stapling needle exit. If there is, clean it up. Then reassemble the stapler and test its function again. 2. Replacing Staples: When the staples are bent or broken, replace them with new ones. First, find the staple replacement port on the stapler, take out the old staples, and insert new ones. Note that the specifications of the new staples should match the original stapler. 3. Checking Power Source and Internal Components: If the stapler does not work, first check if the power source is intact. If it is battery-powered, try replacing the battery. If the power source is fine, it may be a problem with internal components. Disassemble the stapler to check if any internal components are damaged or loose. If necessary, replace or repair them.