订书机常见问题与解决办法 一、常见问题 1. 订书机卡住 在长时间使用或频繁使用后，订书机可能会出现卡住的情况。这通常是由于纸张的碎屑或杂质在订书机内部积累造成的。 2. 订书钉变形 如果订书钉在订书过程中出现变形，可能是由于订书机温度过高或订书钉质量差所导致。 3. 订书机无法正常出钉 这可能是由于订书机的弹簧或其它部件损坏，或者订书钉已经用完。 二、解决办法 1. 订书机卡住的解决办法 首先，关闭订书机并拔出所有的纸张。然后，打开订书机的外壳，用小刷子或吹气的方式清理内部的碎屑和杂质。如果卡住的情况仍然存在，可能需要拆开订书机进行更深入的清理和维修。另外，定期清理和保养可以有效地防止订书机卡住。

2. 订书钉变形的解决办法

【订书机】晨光省力型订书机办大加厚公用号大型多功能学生用大订书器超大丁售价：57.66元 领券价：57.66元 邮费：0.00

首先，确保使用的订书钉质量良好。其次，如果订书机温度过高，可以尝试降低使用频率或等待其冷却后再使用。此外，调整订书机的压力设置也可以防止订书钉变形。 3. 订书机无法正常出钉的解决办法 首先，检查是否还有足够的订书钉。如果没有，需要添加新的订书钉。如果订书钉充足但仍无法出钉，可能需要检查弹簧或其它部件是否损坏。如有必要，可以拆开订书机进行维修或更换部件。同时，定期的维护和保养也可以避免此类问题的发生。 三、英文翻译 Common Issues and Solutions of Bookbinder

I. Common Issues

【订书机】得力10号订书机迷你小号手握式订书器办公小定钉书机器小型携带款售价：59.68元 领券价：59.68元 邮费：0.00

1. Bookbinder gets stuck After long-term or frequent use, the bookbinder may get stuck due to the accumulation of paper debris or impurities inside the machine. 2. Deformation of binding nails If the binding nails deform during the binding process, it may be caused by high temperature of the bookbinder or poor quality of the binding nails. 3. The bookbinder cannot eject nails normally This may be due to damaged springs or other parts of the bookbinder, or the lack of binding nails. II. Solutions 1. Solutions for a stuck bookbinder First, turn off the bookbinder and pull out all the papers. Then, open the shell of the bookbinder and clean the debris and impurities inside with a small brush or by blowing. If the problem persists, it may be necessary to disassemble the bookbinder for more in-depth cleaning and repair. Additionally, regular cleaning and maintenance can effectively prevent the bookbinder from getting stuck. 2. Solutions for deformed binding nails First, ensure that the binding nails used are of good quality. Secondly, if the temperature of the bookbinder is too high, you can try reducing the frequency of use or waiting for it to cool down before using it again. In addition, adjusting the pressure setting of the bookbinder can also prevent the deformation of binding nails. 3. Solutions for a bookbinder that cannot eject nails normally First, check if there are enough binding nails. If not, add new ones. If there are sufficient binding nails but still cannot eject, it may be necessary to check if the springs or other parts are damaged. If necessary, disassemble the bookbinder for repair or replacement of parts. At the same time, regular maintenance and care can also avoid such problems.